教您如何使用奥舒尔ozio四孔点烟器
所属分类：其他
2014-6-30 11:04:54 推荐指数：
1. Scope/简述
1.1 This specification is only suitable for Cigarette lighter,Zhongshan Alfamax
Technology ING mode:DX4S.
本规格书适用于点烟器，中山市亚美斯电子有限公司型号为：DX4S.
1.2 Any query over the specification shall be expressed by R&D department of
Zhongshan Alfamax Technology ING.
对本规格书有疑义时，由中山市亚美斯电子有限公司研发部负责解释.
2. Input Characteristics/输入特性
Item
项目Min
最小值Nominal
额定值Max
最大值Unit
单位
Input DC Voltage
输入直流电压1224Vdc
Input Circuit
输入电流1015A
3. Output Characteristics/输出特性
Item
项目Min
最小值Nominal
额定值Max
最大值Unit
单位
Output DC Voltage
输出直流电压4.7555.25Vdc
1A D+ Voltage
1A D+ D-电压1.922.1Vdc
2.4A D+ D- Voltage
2.4A D+ D-电压2.652.752.85Vdc
P1，P2，P3，P4 Voltage P1，P2，P3，P4电压1224Vdc
P1，P2，P3，P4 current P1，P2，P3，P4电流10A
Ripple & Noise: Measurement is done by 20MHz bandwidth oscilloscope and the
output paralleled a 0.1uF ceramic capacitor and a 10uF electrolysis capacitor.
(test under the condition of rated input and rated output)
纹波与噪声: 量测时示波器选用20MHz带宽限制,输出端要并联一颗0.1uF的陶瓷电容和
一颗10uF的电解电容. (在额定输入及输出的条件下检测)
4. Protection Requirements/保护特性
4.1 Short circuit protection/短路保护
OK
4.2 Over current protection/过流保护
1. 1A过流保护1.4A
2. 2.4A过流保护2.9A
3. P1，P2，P3，P4过流保护10A
4.3 Over voltage protection/过压保护
待定
4.4 Over Temperature Protection/过温保护
125℃
5. Environment Requirements/环境要求
5.1 Operating Temperature and Relative Humidity/工作温度/湿度要求
Operating Temperature :0℃to+40℃/工作温度：0℃to+40℃
Relative Humidity:10%RH to 90%RH/湿度要求：5%RH to 95%RH
5.2 Storage Temperature and Relative Humidity/贮存温度/湿度要求
Storage Temperature：-20℃to+85℃/贮存温度：-20℃to+85℃
Relative Humidity：5%RH to 90%RH/湿度要求：5%RH to 95RH
5.3 Vibration/振动
10 to 300Hz sweep at a constant acceleration of 1.0G(Breadth:3.5mm)for
1Hour foreach of the perpendicular axes X,Y,Z
扫描频率：10 to 300Hz,加速度：1.0G(位移：3.5mm),X,Y,Z三垂直坐标轴向各
振动1小时
5.4 Drop in/跌落
Height:1m:the product should be fell off on the hardwood with the
thickness of 20mm,and the hardwood should be put on the base
of the cement or on the ground without flexibility.Apply two times
on all surface.
跌落高度：1米，并跌落到厚度为20mm的硬木上，且硬木应放在水泥基座或等同
的无弹性地面上，每面各2次
6. Reliability Requirements/可靠性要求
6.1 BURN-IN/烧机:
The power supply shall undergo a MINImum of 4 hours Burn-In test under
full load at35～40℃./电源应在35～40℃和满载条件下烧机4小时.
6.2 MTBF Qualification/平均间隔故障时间估算
The MTBF shall be at least 50,000hours at 25℃,Full load and nominal input
condition平均间隔时间：至少50，000小时，25℃环境及额定输入与满载条件下.
7. EMI/EMS StandarDS/传导与辐射标准
7.1 EMI Standards/EMI 标准
待定
7.2 EMS Standards/EMS标准
待定
8. Safety Standards/安规标准
8.1 Dielectric Strength(Hi-pot)/介电耐压强度(高压)
待定
8.2 Leakage Current/漏电流
待定
8.3 Insulation Resistance/绝缘阻抗
待定
8.4 SAFETY STANDARD/安规标准
待定
9. Component List/元件清单
NO.元件名称规格/参数供应商
1贴片IC LM324 SOP-14
2贴片IC LM78L05 SOT-89
3贴片场效应管 NCE3012S SOT-8Z
4贴片场效应管 UT4800 SOT-8Z
5
6
7
8
9
10
11
12
13
14
15
10. Mach Outline Drawing/外观示意图
图片01
图片02
11.使用说明
一.按1后面点烟孔1相应有输出. 按2后面点烟孔2相应有输出.依次累推